Much cleaner look.Ĭlick on byte 6 and disable bit 4 Disable DRL LED 'wink' on turn signal / parking lights Leaves the low beams off when unlocking the car and just have the DRLs on when it’s dark outside, similar to some other Audis.
Vcds mobile manual#
*Suggestion: Print this and check off the mods you've activated and store it with your owner's manual - Will come handy when you need to re-do the coding after an ECU flash.Ĭoding Light related settings Enable coming home/leaving home function with DRL LED If in doubt, leave well alone! Keep away from the "Bootloader" ! On earlier MMI versions, people managed to activate the bootloader menu and fried their MMI. WARNING!!!! BE CAREFUL!!! Do not mess with settings in the Hidden Menu unless you know what you are doing. To reset the MMI 3G+, press Menu, Big Knob, and Top Right Soft Button simultaneously You know if you have done it right because the red LEDs in the buttons do not illuminate. You may have to have a few attempts - if you don't press them at the exact same moment either CAR or MENU activates. To get to the Hidden Menu, press and hold the CAR and MENU buttons for a few seconds. Reboot the MMI (Press MENU, central MMI knob and top right softkey) Hidden menuĮnable access to the green engineering menu in the MMIĬhange the value from 0 to 1 then Test then Save After a few seconds you will get a screen shown below. Under Port and Protocol Options select TEST as shown below.Īfter you hit test the program will test the connection between the Vag-Com and the car ’ s computer. You will now be taken to the Program Options menu. Click OPTIONS in the bottom right corner. VCDS WILL NOT WORK IF THIS IS NOT DONE*** Starting the VCDSįirst thing you want to do is to make sure the VAG-COM is properly connected to your car. ***HAVE YOUR KEY IN THE IGNITION TURNED ON ACCESSORY MODE (hit the start button once). You will most likely be prompted if you are not. Make sure you are running the most recent version of Ross-Tech's software. Once you have plugged it in, connect it to your laptop device. It is the purple connector located right behind the hood latch under the steering wheel. Hooking up the Vag-Comįirst step is to plug in your Vag-Com to the OBD-2 port.
![vcds mobile vcds mobile](https://m.horje.com/store/wp-content/uploads/2020/03/vlc-screenshot-01-45.png)
Simply follow the instructions and you will be fine. There is no reason to get nervous, you will not do any damage to your car. The most important thing to know is that everything you do in this DIY CAN BE UNDONE. Many people get very intimidated and uneasy about messing around with the car settings on the computer. Take all steps necessary to ascertain that information you receive from this document are correct and have been verified. The information contained in this document is provided on an “as is” basis with no guarantees of completeness, accuracy, usefulness or timeliness. The author assumes no responsibility or liability for any errors or omissions in the content of this document.
Vcds mobile drivers#
Set Audi parking system switch OFF speed 9Īdjust bluetooth microphone sensitivity 9Įnable Remote Operation Windows and Sunroof / Drivers Memory Seat 9ĭisable / memorize / invert Start & Stop: 9Īny action you take upon the information in this document is strictly at your own risk. Parking brake release without seat belt on 8 7Įnabling the default distance setting in the MMI for Adaptive Cruise Control 7Īdd sensitivity menu for Active Lane Assist (if equipped) 8Įnable auto handbrake when shift into Park 8Ĭhange the time before the heated seats auto-change from level 3 to level 2 8 Passenger door mirror dip on selecting reverse 7ĭisabling engine stop when opening driver's door. Increase radio play time after car is turned off 7
![vcds mobile vcds mobile](https://car-diagnostics.eu/media/image/c2/e9/e1/Bild_2020-10-23_164802_200x200@2x.png)
Lap timer / Oil temperature / Boost gauge / Shift light 5Įnable Automatic Gear selection shown in DIS 5ĭisable NAV & Phone warning messages while entering data at speed 5Įnable "Make calls using" feature in cars before MY2013 that have been updated to MMI 0770 6Ĭhanging the brightness range for the dashboard cluster 6 Modifying the High Beam Assist speed threshold 4Įnabling the Daytime Running Lights on/off setting in the MMI 4Įnabling tourist mode setting for headlights in the MMI 4Īctivation of footwell lighting for vehicles without Lighting Pack / Ambient Lighting 4 Enable coming home/leaving home function with DRL LED 3ĭisable DRL LED 'wink' on turn signal / parking lights 3Īdjust DRL LED brightness on turn signal and when the headlights are on 3Įnable Independent Fogs control with high beams 3ĭisable rear side markers in US vehicles 3